ماژول شارژر باتری 5A با قابلیت CV و CC دارای LED وضعیت

ماژول شارژر باتری ۵A با قابلیت CV و CC دارای LED وضعیت

95,000 تومان

موجود در انبار

توضیحات محصول

Description

Power efficient switched mode power supply for use in your projects.

Features

  • Input voltage range:6 to 38VDC(Note:input voltage not exceeding 38V)
  • Output voltage range:1.25-36VDC adjustable
  • Output current: 0-5A
  • Output power: 75W
  • High efficiency up to 96%
  • Built in thermal shutdown function
  • Built in current limit function
  • Built in output short protection function
  • Input reverse polarity protection: None (if required, high current diode in series with the input).
  • Dimensions: L x W x H =61.7*26.2*15mm
  • Weight: 20g

Application Ideas

A. Use as a step-down modules with over current protection capabilities

  1. Adjust the “voltage potentiometer” so that the output voltage reaches the value you want.
  2. Use a multimeter to measure the output short-circuit current with 10mA intervals, while regulating the “current potentiometer” so that the output current reaches a predetermined over current protection value. (For example, the meter displays the current value of 4A, then you can use the module to a maximum current of 4A)
  3. Connect to the load.

B. Use as a battery charger

  1. Make sure you need to charge the battery float voltage and charging current; (if lithium parameters 3.7V/2200mAh, then the float voltage is 4.2V, the maximum charging current 1C, ie 2200mA)
  2. Under no-load conditions, adjust the “Voltage potentiometer” so that the output voltage reaches the float voltage; (if to 3.7V rechargeable lithium battery, the output voltage can be adjusted to 4.2V)
  3. Use a multimeter to measure the output short-circuit current with 10mA intervals, while regulating the “current potentiometer” so that the output current reaches a predetermined Charging current value.
  4. Charge turn lamp current factory default is 0.1 times the charging current; (Battery during charging current is gradually reduced, if the charge current setting is 1A, then when the charge current is less than 0.1A, blue lights turned off, the green light is on, which means that the battery is fully charged)
  5. Connect to the battery.

(۱,۲,۳,۴ steps as: Output is unloaded, do not connect the battery)

C. Use as a LED constant current driver module

  1. Adjust the “voltage potentiometer” so that the output voltage reaches the value you want.
  2. Use a multimeter to measure the output short-circuit current with 10A intervals, while regulating the “current potentiometer” so that the output current reaches a predetermined LED operating current.
  3. Connect LED, work.

(۱,۲ steps as: Output is unloaded, do not connect LED)

همه نقد ها

  1. reza:goodarzi (مالک تأیید ‌شده):

    سلام میخاستم سوال کتم اگه به این ماژول کآهنده ۵ آمپر ورودیش ۶ آمپر باشه مشکلی پیش نمیاد ؟

  2. reza:goodarzi (مالک تأیید ‌شده):

    سلام میشه به ورودی ماژول ۶ امپر بدیم مشکلی پیش نمیاد

  3. admin:

    سلام
    میتونید توی ورودی ولتاژ ۵ تا ۳۰ ولت با هر جریانی که باشه بهش بدید مشکلی به وجود نمیاد.

  4. admin:

    سلام
    مشکلی نداره

افزودن یک بررسی